Our John Deere Gator HPX 4X4 OEM Service Manual is a brand new original OEM (Original Equipment Manufacturer) manual for this machine. Tractor OEM. Find great deals for John Deere 6×4 Gator Technical Service Manual CD TMCD. Shop with confidence on eBay!. Find great deals for John Deere 4×2 / 6×4 Gator Workshop Repair Manual on CD. Shop with confidence on eBay!.
|Published (Last):||3 December 2006|
|PDF File Size:||17.3 Mb|
|ePub File Size:||17.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
DO NOT operate engine without air cleaner element and rubber dust unloading valve installed. If coolant temperature indicator comes on while engine is running, stop engine and add more coolant mixture to radiator. Push radiator back into place and secure with original hardware. Failure to check the oil level regularly could lead to serious engine problems if oil level is low: Check and remove any obstructions to brake linkage attached to output shafts on both sides of transaxle.
The radiator may be hot and can burn skin. Use oil viscosity based on the expected air temperature range during the period between oil changes. Locate the fuel filter A at the front of the engine compartment.
If radiator drain plug is seized, lower radiator hose can be removed for draining purposes. Follow all service procedures exactly. Do not allow bottom of hose B to touch bottom of bottle or bend upwards out of coolant. This mixture will provide freeze protection to degrees C degrees F. Do not overfill crankcase with oil. If engine is hard to start or runs rough, check the troubleshooting section of this manual. Allow coolant to drain into a container.
The radiator will be hot and can burn skin. Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.
Built-up pressure may cause explosive release of coolant when the radiator cap is removed: Allow engine to cool and suction back any needed coolant from overflow reservoir. Remove screw securing spark arrestor A to muffler exhaust pipe.
Follow the directions on the container for correct mixture ratio. Make sure end of hose C is positioned slightly above bottom of reservoir.
Turn radiator cap slowly to the stop to release system pressure. Remove radiator drain plug or disconnect lower radiator hose D. Carburetor is calibrated by the engine manufacturer and is not adjustable. Do not open canister unless required for scheduled service. The engine and components will be hot if the engine has been running.
Warranty repairs must be performed by an aervice John Deere dealer. Do not spray water on a hot engine or transaxle. Place a drain pan or cloth under hoses to catch any fuel that may be left in hoses. Fuel vapors are explosive and flammable: If not equipped to perform this work, see your John Deere dealer for service. Bleed screw uses a special aluminum seal washer. Continue running engine until cooling fan starts, indicating the engine and coolant has reached operating temperature.
After all coolant has drained, bator radiator plug or connect radiator hose and tighten the engine block drain screws. Install new filter by turning it to the right clockwise until rubber gasket contacts filter base.
Change the oil more often if the vehicle is used in extreme conditions: Check element of fuel filter for debris. After all solution has drained, install radiator drain plug or hose and tighten engine block drain screws. Manuap may occur to cast aluminum parts.
Make sure air intake tube A is free from deete. Use coolant with conditioner or add conditioner to coolant before using. See the label on your antifreeze container or consult your John Deere dealer to obtain the latest information and recommendations.
Lift radiator slightly to access drain plug C. Install side screen after cleaning. Wipe off filter base on engine.
Determine cause of this condition and correct. Check condition of all hoses. Using incorrect coolant mixture can damage the radiator: Change the oil more often if the mmanual is used in extreme conditions:.
Put a light coat of clean engine oil on gasket of new oil filter. Replace if dirt or sediment is visible on element.
Coolant cannot be drawn into cooling system if suction hose is installed wrong. Pull off the differential lock lever knob.
Fill reservoir as needed so it contains 25 – 50 mm 1 -2 in.
Tighten filter an additional one-half turn.